Niscomed CMS 7000 Plus Multi Parameter Patient Monitor

– The Niscomed CMS 7000 Plus Multi Parameter Patient Monitor has a 12.1 inch colour TFT LCD display with waveforms upto 8 Channels
– The patient monitoring system is portable supported by a streamline handle design
– The patient monitor is suitable for Adult to Neonate patients
– The monitoring system allows to measure one channel ECG anytime, anywhere you like
– The parient monitoring machine displays ECG waveform, heart rate, analysis results and battery status on the backlit LCD
– The measurement results transmission to PC by USB mode
– The patient monitoring device is equipped with an auto power-off while no key is pressed in 30 seconds
– The auto-evaluation is based on detected heart data
– 2 batteries can take at least 500 times measurement
– Technical Specifications for ECG:
– 5-lead or 12-lead selectable
– Input: 5-lead: RA; LA; RL; LL; V or R; L; N; F; C
– Lead selection: I; II; III; avR; avL; avF; Vx; CAL
– Gain selection: ×0.25,×0.5,×1,×2,auto
– Sweep speed: 12.5mm/s, 25mm/s, 50mm/s
– Accuracy: ±1bpm or ±1%, whichever is greater
– Protection: Withstand 4000V AC/50Hz voltage in isolation against electrosurgical and defibrillation
– Calibration signal: 1mV±5%
– Operation modes: Diagnostic, Monitor, Surgery
– Heart rate range: Adult: 15-300bpm Paediatric/ Neonatal: 15-350bpm
– Measurement range: -2.0mV~2.0mV
– S-T detection: YES, Arrhythmia analysis: YES
– Alarm: YES, audible and visual alarm, alarm events recallable
– Technical Specifications for NIBP:
– Method: Oscillometry
– Operation modes: Manual/Automatic/STAT
– Measurement unit: mmHg/KPa selectable
– Gain selection: ×0.25,×0.5,×1,×2,auto
– Measurement types: Systolic, Diastolic, Mean
– Measurement range: Adult: 10-270mmHg
– Over-pressure protection: YES
– Resolution: 1mmHg
– Accuracy: The mean error shall be less than ±5 mmHg ,the standard deviation shall be less than ±8mmHg
– Alarm: Systolic,Diastolic,Mean
– Technical Specifications for SPO2:
– Measurement range: 0-100%
– Accuracy: ±2%(70~100%);0~69% unspecified
– Alarm range: 0-100%
– Technical Specifications for Respiration:
– Method: RA-LL impedance
– Measurement range:Adult: 0-120rpm, paediatric/neonatal:0-150rpm
– Apnea alarm: YES
– Technical Specifications for IBP:
– Channel: 2 channels
– Pressure transducer:Sensitivity: 5( mV/V/mmHg)
– Transducer sites: ART, PA, CVP, RAP, LAP, ICP
– Alarm range: -10~300mmHg
– Vital signs are an important component of patient care. They determine which treatment protocols to follow, provide critical information needed to make life-saving decisions, and confirm feedback on treatments performed. Accurate, documented vital signs are a very important part of EMS (Emergency Medical Support) and to monitor the same; Patient Monitoring Systems are manufactured
– Patient Monitoring systems are designed to help enhancing the patient care and improve clinical performance. This comprehensive solution fits securely into the hospital’s IT environment to capture timely patient data and feed it securely to the EMR (Electronic Medical Record).
– A patient monitor is an electronic medical device that consists of one or more monitoring sensors, a processing component, and a screen display (also called a “monitor”) that provide and record for medical professionals a patient’s medical vital signs like body temperature, blood pressure, pulse rate etc..
– Patient monitoring systems are used in hospitals, nursing homes, emergency care centres and health care set ups to monitor and review the vital physiological signs of a patient. Most patient monitoring systems are able to monitor the patient’s respiration, oxygen saturation in blood, invasive and non invasive blood pressure, electrocardiograph, body temperature etc.. Various sensors and electrodes are used to measure these signs including the ECG electrodes, SpO2 finger sensor, blood pressure cuff, temperature probe etc..